Water Eject iPhone
Remove Water from Speaker in 30 Seconds

Before you run the tool, it’s worth confirming that water in the speaker is actually your issue. Here are the telltale signs:

The process takes about 90 seconds total, 30 seconds of actual ejection plus a moment of setup. Here’s exactly what to do:

Our tool offers four frequency options. For iPhone specifically, here’s what each one does and when to use it:

The water eject technique works on every iPhone with a speaker – which is all of them from iPhone 6 onwards. The main difference between models is water resistance rating and speaker layout, both of which affect how susceptible they are to water getting in, not whether the tool can help once it’s there.

The tool works well on its own, but a few small tweaks make a noticeable difference – especially for heavier water exposure or when using the tool on older iPhone models.

Running the tool is step one. Here’s how to make sure your iPhone fully recovers:

1. Test your audio – play music or a video at medium volume. If it sounds clear, you’re done. If there’s still slight muffling, run one more cycle.
2. Let it air dry for 30 minutes – even if audio sounds perfect, moisture can linger in the grille mesh. Leave the phone in a dry, well-ventilated spot (not in direct sunlight or near a heater) for half an hour.
3. Do not use a hair dryer or compressed air – heat can damage the speaker membrane and adhesives. Compressed air can force water deeper into the device rather than out.
4. Don’t place it in rice – the “rice trick” is widely debunked. Rice does not absorb moisture from inside electronic devices effectively and can introduce dust and starch into ports. Air drying is always better.
5. Watch for the charging port alert – if your iPhone shows a liquid detection warning when you try to charge it, that’s normal after water exposure. Use wireless charging (MagSafe or Qi) in the meantime, or wait until the alert clears.
6. Run a sound test the next day – some residual moisture deep in the grille mesh can take overnight to evaporate. If sound seems slightly off the same day, a fresh round of eject cycles the following morning often finishes the job.

The eject tool is designed for speaker water removal – not for addressing internal water damage. There are situations where no online tool can substitute for professional repair, and it’s important to recognise them:

• iPhone won’t turn on – if the device is completely unresponsive, this suggests water has reached the logic board. Do not attempt to power it on. Take it to an Apple Authorised Service Provider immediately.
• Screen is damaged or discoloured – water behind the display indicates internal penetration beyond what IP ratings can protect. Professional disassembly and drying is required.
• Saltwater or pool water exposure – chlorine and salt are far more corrosive than fresh water. Even if your iPhone seems fine after saltwater exposure, have it inspected by a technician because corrosion can develop over days or weeks.
• iPhone 6 or earlier submerged – without any water resistance rating, submersion in older models typically reaches the logic board. Consider professional inspection even if it appears to be working.
• You can smell burning – this indicates a short circuit and is a sign of serious internal damage. Stop using the device and consult a repair professional.
• Battery is swelling – a puffy or deformed battery is a fire and explosion risk. Do not use or charge the device. Contact Apple or a certified technician immediately.

A common question we get: “Apple Watch has a built-in Water Lock feature – why doesn’t iPhone have the same thing?”

The short answer is that Apple Watch’s Water Lock is built directly into watchOS, and using the Digital Crown to “unlock” it triggers a 165 Hz tone that ejects water from the speaker. It’s essentially the same technology as our tool – just baked into the operating system rather than accessed via a browser.

Apple has not added an equivalent feature to iOS at the time of writing. There’s no built-in “water eject” shortcut or Siri command on iPhone. The closest workaround some users know is creating a Shortcut that plays a specific audio file – but that requires setup, a specific file, and only plays through whatever audio route is currently active.

EjectWater.com fills that gap. We generate the same 165 Hz sine wave that Apple uses on Apple Watch, delivered directly through your iPhone’s speaker – right in the browser, no setup required. The physics are identical. The result is the same.

Got other devices with water in the speaker? We have you covered: